INSTRUCTIONS-PARTS LIST
308–739
Rev. A
This manual contains important
warnings and information.
READ AND KEEP IT FOR REFERENCE.
First choice when
quality counts.t
INSTRUCTIONS
STUBBY SIZE
15:1 Ratio Monarkr Pump
Part No. 239–327, Series A
105 bar (10.5 MPa, 1500 psi) Maximum Fluid Working Pressure
7 bar (0.7 MPa, 100 psi) Maximum Air Input Pressure
Refer to page 2 for the Table of Contents.
07196
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
ECOPYRIGHT 1997, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
WARNING
INJECTION HAZARD
Spray from the gun, hose leaks, or ruptured components can inject fluid into your body and cause
extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin
can also cause serious injury
.
D
Fluid injected into the skin might look like just a cut, but it is a serious injury
cal attention.
.
Get immediate medi-
D
D
D
D
D
D
D
D
D
Do not point the gun at anyone or at any part of the body
.
Do not put your hand or fingers over the spray tip.
Do not stop or deflect leaks with your hand, body, glove or rag.
Do not “blow back” fluid; this is not an air spray system.
Always have the tip guard and the trigger guard on the gun when spraying.
Check the gun diffuser operation weekly. Refer to the gun manual.
Be sure the gun trigger safety operates before spraying.
Lock the gun trigger safety when you stop spraying.
Follow the Pressure Relief Procedure on page 8 whenever you: are instructed to relieve pres
sure; stop spraying; clean, check, or service the equipment; and install or clean the spray tip.
-
D Tighten all fluid connections before operating the equipment.
D
Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately.
Permanently coupled hoses cannot be repaired; replace the entire hose.
D
Use only Graco approved hoses. Do not remove any spring guard that is used to help protect the
hose from rupture caused by kinks or bends near the couplings.
MOVING PARTS HAZARD
Moving parts, such as the air motor piston, can pinch or amputate your fingers.
D
D
Keep clear of all moving parts when starting or operating the pump.
Before servicing the equipment, follow the Pressure Relief Procedure on page 8 to prevent the
equipment from starting unexpectedly
.
308-739
3
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury
.
D
D
Ground the equipment and the object being sprayed. Refer to Grounding on page 5.
If there is any static sparking or you feel an electric shock while using this equipment, stop spray-
ing immediately Do not use the equipment until you identify and correct the problem.
.
D
Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed.
D
D
D
D
D
D
Keep the spray area free of debris, including solvent, rags, and gasoline.
Electrically disconnect all equipment in the spray area.
Extinguish all open flames or pilot lights in the spray area.
Do not smoke in the spray area.
Do not turn on or off any light switch in the spray area while operating or if fumes are present.
Do not operate a gasoline engine in the spray area.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
D
D
Know the specific hazards of the fluid you are using.
Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
D
Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer
.
4
308-739
Installation
NOTES:
D
Pump: Use a ground wire and clamp. See Fig.1.
Loosen the grounding lug locknut (W) and washer
(X). Insert one end of a 12 ga (1.5 mm@) minimum
ground wire (Y) into the slot in lug (Z) and tighten
the locknut securely. Connect the other end of the
wire to a true earth ground. For a ground wire and
clamp, order Part No. 237–569.
D
Reference numbers and letters in parentheses in
the text refer to the callouts in the figures and
drawings.
D
Always use Genuine Graco Parts and Accessories,
available from your Graco distributor. If you supply
your own accessories, be sure they are adequately
Z
Y
sized and pressure-rated to meet the system’
s
requirements.
D
Fig. 2 is only a guide for selecting and installing
system components and accessories. Contact your
Graco distributor for assistance in designing a
system to suit your particular needs.
Prepare the Operator
All persons who operate the equipment must be
trained in the safe, efficient operation of all system
components as well as the proper handling of all fluids.
All operators must thoroughly read all instruction
manuals, tags, and labels before operating the
equipment.
W
X
02464
Fig. 1
D
Air and fluid hoses: Use only electrically conductive
hoses with 150 m (500 ft) maximum combined hose
Prepare the Site
length to ensure grounding continuity
.
Ensure that you have an adequate compressed air
supply. Refer to the performance chart on page 15 to
find the air consumption of your pump.
D
D
Air compressor: Follow manufacturer’s
recommendations.
Spray gun or dispensing valve: Connect to a
properly grounded fluid hose and pump.
Keep the site clear of any obstacles or debris that
could interfere with the operator’s movement.
D
D
D
Object being sprayed: Follow your local code.
Fluid supply container: Follow your local code.
Have a grounded, metal pail available for use when
flushing the system.
Mounting the Pump
Solvent pails used when flushing: Follow your local
code. Use only metal pails, which are conductive,
placed on a grounded surface. Do not place the
pail on a nonconductive surface, such as paper or
cardboard, which interrupts the grounding
continuity.
Mount the pump (A) to suit the type of installation
planned. The pump dimensions and mounting hole
layout are shown on page 13. If you are using a wall
bracket (B), check that the wall is strong enough to
support the weight of the equipment, hoses, fluid, and
stress caused when the pump is in operation. Mount
D To maintain proper grounding continuity when
flushing or relieving pressure, always hold the metal
part of the spray gun firmly to the side of a
grounded metal pail, then trigger the gun.
the wall bracket 1.5 m (5 ft) above the floor
.
Grounding
WARNING
FIRE AND EXPLOSION HAZARD
Before operating the pump, ground the
system as explained below. Also read
the section FIRE AND EXPLOSION
HAZARD on page 4.
308-739
5
Installation
Typical Installation
KEY
A
B
C
D
Pump
Wall bracket
Air line lubricator
Bleed-type master air valve (required for pump)
See Warning on page 7 for part number
.
E
F
G
H
J
Pump air regulator
Air line filter
Bleed-type master air valve (for accessories)
Electrically conductive air supply hose
Fluid drain valve (required)
See Warning on page 7 for part numbers.
Fluid filter
Electrically conductive fluid supply hose
Spray gun
Fluid suction hose
F
G
K
L
M
N
P
R
Y
Air line moisture trap and drain valve
Pump runaway valve
Ground wire (required)
E
D
C
R
Part No. 237–569. See page 5 for installation instructions
H
A
M
Y
B
P
K
J
N
L
07198
Fig.
2
6
308-739
Installation
Air Line Accessories
System Accessories
Install the following accessories in the order shown in
Fig. 2, using adapters as necessary:
WARNING
bleed-type master air valve (D) and a fluid drain
valve (J) are required in your system. These
accessories help reduce the risk of serious injury
including fluid injection, splashing in the eyes or on
the skin, and injury from moving parts if you are
adjusting or repairing the pump.
D
D
Air line lubricator (C)
Provides automatic air motor lubrication.
A
Bleed-type master air valve (D)
Required in your system to relieve air trapped
between it and the air motor when the valve is
closed (see the WARNING at left). Be sure the
bleed valve is easily accessible from the pump, and
is located downstream from the air regulator (E).
The bleed-type master air valve relieves air trapped
between this valve and the pump after the air is
shut off. Trapped air can cause the pump to cycle
unexpectedly. Locate the valve close to the pump.
Order Part No. 113–333.
D
Air regulator (E)
Controls pump speed and outlet pressure by
adjusting the air pressure to the pump. Locate the
regulator close to the pump, but upstream from the
bleed-type master air valve (D).
The fluid drain valve assists in relieving fluid pres
sure in the displacement pump, hose, and gun.
-
T
riggering the gun to relieve pressure may not be
D
D
Pump runaway valve (R)
Senses if the pump is running too fast and shuts of
the air supply to the motor. A pump which runs too
fast can be seriously damaged.
sufficient. Order one of the following:
f
Part No. Description
238–635 1/4 npt (mbe), carbon steel
210–657 1/4 npt (mbe), carbon steel
210–658 3/8 npt (mbe), carbon steel
210–659 1/4 npt x 3/8 npt (mbe), carbon steel
239–018 1/4 npt (mbe), stainless steel
Air line filter (F)
Install an air line filter (F) and a moisture trap and
drain valve (P) to help remove moisture and
contaminants from the compressed air supply
.
235–992 1/4 npt x 3/8 npt (mbe), stainless steel
D Second bleed-type air valve (G)
Air and Fluid Hoses
Isolates the air line accessories for servicing.
Locate upstream from all other air line accessories.
Be sure all air and fluid hoses are properly sized and
pressure-rated for your system. Use only electrically
conductive air and fluid hoses. Use a 13 mm (1/2 in.)
I.D. (minimum) air hose (H) to supply air to the pump.
Fluid Line Accessories
Install the following accessories in the positions shown
in Fig. 2, using adapters as necessary:
Fluid hoses must have spring guards on both ends.
Connect a fluid hose (L) to the pump’s 3/8 npt(f) fluid
outlet. Use of a short whip hose between the main
fluid hose and the gun (M) allows freer gun movement.
D Fluid drain valve (J)
Required in your system to relieve fluid pressure in
the hose and gun (see the WARNING at left).
Install the drain valve so that it points down and the
handle points up when it is opened.
Connect a fluid suction hose or tube (N) to the pump’
s
3/4 npt(m) fluid intake.
D Fluid filter (K)
Filters harmful particles from the fluid.
D Spray gun (M)
Dispenses the fluid. The gun shown in Fig. 2 is an
airless spray gun.
308-739
7
Operation
Pressure Relief Procedure
Packing Nut/Wet-Cup
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure at left.
WARNING
INJECTION HAZARD
The system pressure must be manually
relieved to prevent the system from
starting or spraying accidentally. Fluid
Keep the packing nut/wet-cup (V) filled with Graco
Throat Seal Liquid (TSL) or compatible solvent to help
prolong the packing life. Check the tightness of the
packing nut weekly; tighten just enough to prevent
leakage; do not overtighten it. See Fig. 3 on page 11.
Relieve the pressure before adjusting the packing nut
or adding TSL.
under high pressure can be injected through the
skin and cause serious injury. To reduce the risk of
an injury from injection, splashing fluid, or moving
parts, follow the Pressure Relief Procedure
whenever you:
D
D
D
D
are instructed to relieve the pressure,
stop spraying,
check or service any of the system equipment,
or install or clean the spray tip.
Starting and Adjusting the Pump
Begin these steps before you install the spray tip.
1. Lock the gun trigger safety
.
1. Ensure that the air regulator (E) and bleed-type
master air valve (D) are closed. See Fig. 2 on
page 6.
2. Shut off the air supply to the pump.
3. Close the bleed-type master air valve (required in
your system).
2. Connect a suction hose (N) to the pump’s fluid
inlet, or lower the pump into a fluid supply
container.
4. Unlock the gun trigger safety
.
3. Hold a metal part of the spray gun (M) firmly to the
side of a grounded metal pail and hold the trigger
open.
5. Hold a metal part of the gun firmly to the side of a
grounded metal pail, and trigger the gun to relieve
pressure.
4. Open the pump’s bleed-type master air valve (D).
6. Lock the gun trigger safety
.
5. Slowly open the air regulator (E) until the pump
starts; approximately 2.8 bar (0.28 MPa, 40 psi).
7. Open the drain valve (required in your system),
and have a container ready to catch the drainage.
6. Cycle the pump slowly until all the air is pushed
out and the pump and hoses are fully primed.
8. Leave the drain valve open until you are ready to
spray again.
7. Release the spray gun trigger and lock the trigger
safety. The pump should stall against pressure
If you suspect that the spray tip or hose is completely
clogged, or that pressure has not been fully relieved
after following the steps above, very slowly loosen the
tip guard retaining nut or hose end coupling and relieve
pressure gradually, then loosen it completely. Then
clear the tip or hose.
when you release the trigger
.
WARNING
T
o reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure at left.
Flush the Pump Before First Use
The pump is tested with lightweight oil, which is left in
to protect the pump parts. If the fluid you are using
may be contaminated by the oil, flush it out with a
compatible solvent before using the pump. If the pump
is being used to supply a circulating system, allow the
solvent to circulate until the pump is thoroughly
flushed. See Flushing the Pump on page 9.
8. Relieve the pressure
.
9. Install the spray tip in the gun.
8
308-739
Operation
Flushing the Pump
WARNING
COMPONENT RUPTURE HAZARD
o reduce the risk of overpressurizing
your system, which could cause
WARNING
T
FIRE AND EXPLOSION HAZARD
Before flushing, read the section FIRE
AND EXPLOSION HAZARD on page
4. Be sure the entire system and
flushing pails are properly grounded.
Refer to Grounding on page 5.
component rupture and serious injury
,
never exceed the specified maximum air input
pressure to the pump (see
page 14).
Technical Data on
10. Control the pump speed and fluid pressure with
the air regulator (E). Always use the lowest air
pressure necessary to get the desired results.
Higher pressure causes premature spray tip and
Flush with a fluid that is compatible with the fluid you
are pumping and with the wetted parts in your system.
Check with your fluid manufacturer or supplier for
pump wear
.
recommended flushing fluids and flushing frequency
.
Always flush the pump before fluid dries on the
displacement rod.
11. With the pump and lines primed, and with
adequate air pressure and volume supplied, the
pump starts and stops as the spray gun is opened
and closed. In a circulating system, the pump runs
continuously and speeds up or slows down as
supply increases or decreases until the air supply
is shut off.
CAUTION
Never leave water or water-base fluid in the pump
overnight. If you are pumping water-base fluid, flush
with water first, then with a rust inhibitor such as
mineral spirits. Relieve the pressure, but leave the
rust inhibitor in the pump to protect the parts from
corrosion.
CAUTION
Never allow the pump to run dry of the fluid being
pumped. A dry pump will quickly accelerate to a high
speed, possibly damaging itself. If your pump accel
-
WARNING
erates quickly, or is running too fast, stop it immedi
-
T
o reduce the risk of serious injury whenever you
ately and check the fluid supply. If the supply con
-
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
tainer is empty and air has been pumped into the
lines, refill the container and prime the pump and the
lines with fluid, or flush and leave it filled with a
compatible solvent. Be sure to eliminate all air from
the fluid system.
1. Relieve the pressure.
2. Remove the spray tip from the gun.
Shutdown and Care of the Pump
3. Hold a metal part of the gun firmly to the side of a
grounded metal pail.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
4. Start the pump. Always use the lowest possible
fluid pressure when flushing.
5. Trigger the gun.
6. Flush the system until clear solvent flows from the
gun.
For overnight shutdown, relieve the pressure and
always stop the pump at the bottom of the stroke to
prevent the fluid from drying on the exposed
,
7. Relieve the pressure.
displacement rod and damaging the throat packings.
Always flush the pump before the fluid dries on the
displacement rod. See Flushing the Pump.
308-739
9
Troubleshooting
1. Relieve the pressure.
WARNING
2. Check all possible problems and solutions before
disassembling pump.
T
o reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
Problem
Cause
Restricted line or inadequate air
Solution
Pump fails to operate.
Clear; increase air supply.
supply.
Insufficient air pressure; closed or
clogged air valves, etc.
Open; clean (be sure to use air fil
ter).
-
Exhausted fluid supply
.
Refill; purge all air from pump and
fluid lines.
Damaged air motor
.
Service air motor. See manual
307–043.
Dried fluid seizure of displacement
rod.
Clean, check or replace throat pack
ings. See manual 306–981.
Always stop pump at bottom of
stroke and keep wet-cup filled with
compatible solvent.
-
Pump operates but output is low on Restricted line or inadequate air
Clear; increase air supply.
both strokes.
supply.
Insufficient air pressure; closed or
clogged air valves, etc.
Open; clean (be sure to use air
filter).
Clogged fluid line, valves, etc.
Packing nut is too tight.
Clear* (be sure to use fluid filter).
Loosen (see page 8).
Pump operates but output is low on Held open or worn intake valve.
downstroke.
Clear; service. See manual
306–981.
Pump operates but output is low on Held open or worn fluid piston valve Clear; service. See manual
upstroke.
or packings.
306–981.
Erratic or accelerated operation.
Exhausted fluid supply
.
Refill; purge all air from pump and
fluid lines.
Held open or worn intake valve.
Clear; service. See manual
306–981.
* To determine if the fluid hose or gun is obstructed, relieve the pressure and disconnect the fluid hose, and place
a container at the pump fluid outlet to catch any fluid. Turn on the air just enough to start the pump; about 1.4 to
2.8 bar (0.14 to 0.28 MPa, 20 to 40 psi). If the pump starts when the air is turned on, the obstruction is in the
fluid hose or gun.
10
308-739
Service
Disconnecting the Displacement Pump
Reconnecting the Displacement Pump
1. Lubricate the o-ring (6) and check that it is in place
on the displacement rod (U).
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
2. Orient the fluid outlet (S) to the air inlet (T) as
noted in step 2 under Disconnecting the
Displacement Pump Position the displacement
.
pump (2) on the tie rods (3). See Fig. 3.
1. Flush the pump if possible. Stop the pump at the
bottom of its stroke. Relieve the pressure.
3. Screw the displacement rod (U) into the shaft of
the air motor (1) until the pin holes are aligned.
Install the cotter pin (5). Screw the locknuts (4)
2. Disconnect the air and fluid hoses. Remove the
pump from its mounting. Note the relative position
of the fluid outlet (S) to the air inlet (T). See Fig. 3.
onto the tie rods (3) loosely
.
4. Mount the pump and reconnect all hoses.
Reconnect the ground wire if it was disconnected
during repair. Tighten the packing nut (V). Fill the
wet-cup with Graco Throat Seal Liquid or
compatible solvent.
3. Unscrew the tie rod locknuts (4) from the tie rods
(3). Remove the cotter pin (5). Carefully pull the
displacement pump (2) off the air motor (1).
Unscrew the displacement rod (U) from the air
motor (1). Inspect the o-ring (6).
5. Tighten the tie rod locknuts (4) evenly, and torque
to 20 to 27 NSm (15 to 20 ft–lb). Start the pump
and run it at about 2.8 bar (0.28 MPa, 40 psi) air
4. Refer to manual 306–981 for displacement pump
service. To service the air motor, refer to manual
307–043.
pressure, to check that it is operating properly
.
1
2
Lubricate.
1
T
Torque to 20 to 27 NSm (15 to 20 ft-lb).
6
U
1
3
V
5
4
2
S
2
07197
Fig.
3
308-739 11
Parts
Part No. 239–327, Series A
Ref
No.
Part
No.
Description
Qty
1
6
1
2
3
205–997 AIR MOTOR
see manual 307–043
223–587 DISPLACEMENT PUMP ASSY
see manual 306–981
164–722 ROD, tie; carbon steel; 111 mm
(4.375 in.) shoulder to shoulder
101–566 NUT, lock, 3/8–16
1
1
,
3
3
1
1
4
5
6
101–946 PIN, cotter, stainless steel
154–771 O-RING; buna-N
3
5
4
2
07197
12
308-739
Dimensions
Mounting Hole
Layout
A 111.3 mm (4.38 in.) diameter
B 64 mm (2.5 in.)
C
D
127 mm (5.0 in.)
7.1 mm (0.28 in.) diameter
Use Gasket
161–023
(order separately)
D
(air inlet)
B
D
A
E
A
(fluid outlet)
B
C
F
(fluid intake)
07196
Dimension
Measurement
A
B
D
E
F
382.5 mm (15.06 in.)
681 mm (26.81 in.)
1/2 npt(f)
3/8 npt(f)
3/4 npt(m)
308-739 13
Technical Data
Category
Data
Ratio
15:1
Maximum fluid working pressure
Maximum air input pressure
105 bar (10.5 MPa, 1500 psi)
7 bar (0.7 MPa, 100 psi)
1.9 liters/min (0.5 gpm)
82_C (180_F)
Fluid flow at 60 cycles per minute
Maximum pump operating temperature
Wetted parts
Refer to manual 306–981.
Sound Pressure Levels (dBa)
(measured at 1 meter from unit)
Input Air Pressures at 15 cycles per minute
Air Motor
2.8 bar (0.28 MPa, 40 psi)
4.8 bar (0.48 MPa, 70 psi)
7 bar (0.7 MPa, 100 psi)
77.7 dB(A)
Monark
73.3 dB(A)
75.9 dB(A)
Sound Power Levels (dBa)
(tested in accordance with ISO 9614–2)
Input Air Pressures at 15 cycles per minute
Air Motor
2.8 bar (0.28 MPa, 40 psi)
4.8 bar (0.48 MPa, 70 psi)
7 bar (0.7 MPa, 100 psi)
91.4 dB(A)
Monark
87.0 dB(A)
89.7 dB(A)
14
308-739
Technical Data
Performance Chart
KEY:
Fluid Outlet Pressure – Black Curves
Air Consumption – Gray Curves
cycles per minute
psi
bar, MPa
1500
19
37
54 60
71
88
scfm
m#/min
A
B
C
7 bar (0.7 MPa, 100 psi) Air Pressure
4.9 bar (0.49 MPa, 70 psi) Air Pressure
2.8 bar (0.28 MPa, 40 psi) Air Pressure
104, 10.4
25
1250
A
B
0.70
87, 8.7
T
o find fluid outlet pressure (bar/MPa/psi) at a
20
0.56
specific fluid flow (lpm/gpm) and operating air
pressure (bar/MPa/psi):
1000
70, 7
1. Locate desired flow along bottom of chart.
15
0.42
A
B
750
2. Follow vertical line up to intersection with
selected fluid outlet pressure curve (black).
Follow left to scale to read fluid outlet pressure.
51, 5.1
10
0.28
500
34, 3.4
To find pump air consumption (m#/min or scfm)
at a specific fluid flow (lpm/gpm) and air pressure
(bar/MPa/psi):
C
5
0.14
C
250
1. Locate desired flow along bottom of chart.
17, 1.7
2. Read vertical line up to intersection with
selected air consumption curve (gray). Follow
right to scale to read air consumption.
0
0.0
0.2
0.4
0.6
0.8
1.0
gpm
liters/minute
0.8
1.5
2.3
3.0
3.8
FLUID FLOW (TEST FLUID: NO. 10 WEIGHT OIL)
308-739 15
The Graco Warranty and Disclaimers
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from
defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the
exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of
sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment
is installed, operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or
substitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility
of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS
WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD
BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches,
hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in
making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties
reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures
judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Graco Phone Number
TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you:
1–800–367–4023 Toll Free
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Sales Offices: Minneapolis, Detroit, Los Angeles
Foreign Offices: Belgium, Canada, England, Korea, France, Germany, Hong Kong, Japan
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
PRINTED IN U.S.A. 308–739 September 1997
16
308-739
|