BIG FOOT PANEL WAGON
32826
ASSEMBLY & OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Read this material before using this product.
Failure to do so can result in serious injury.
SaVe THiS manual.
Copyright© 1999 by Harbor Freight Tools®. All rights reserved. No portion of this manual
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Before Operating
Before using your Wagon, any part that appears damaged should be carefully checked to determine that it will
operate properly and perform its intended function.
Before operating your Big Foot Panel Wagon, check for damaged parts.
Do not over inflate the tires. Check the instructions on the tires for proper air pressure.
Inspect all parts for sharp edges before using your wagon. Great care has been taken to assure smooth
surfaces but a complete inspection before using could prevent injury.
Periodically inspect all nuts, bolts and tires to make certain that they are tight and properly inflated.
Make certain to park the Wagon on a level and secure area.
Assembly
Your Wagon comes unassembled. For assistance with assembly, please refer to the parts list and the
Assembly diagram on page 5. It is recommended that your wagon be assembled with the Tray placed over
sawhorses or sturdy cartons. This allows easy access to the wagon and protects it from damage during
assembly.
Do not use excessive force when tightening the screws, as this may result in damage to the support arms.
Step 1)
Step 2)
With the Tray (part A) upside down so the bottom is facing upward, place it
over saw horses or sturdy cartons.
Attach the Rear Axle Assembly (part H) to the Tray (A) using two (2) 1/2”
Bolts. Line up the Rear Axle Assembly with the holes located at the very back of
the Wagon. Insert the Bolt so that the small washers, small lock washers and cap
nuts (found in Hardware bag K) are screwed on from the underside of the wagon.
Step 3)
Step 4)
Slide each of the Rear Axle Braces (part I) over the end of each Rear Axle until
they sit firmly to the inside of the Rear Axle Assembly (H). Line up the
end of the Braces with the holes in the wagon. Using two (2) 1/2” Bolts,
insert the bolts from the top of the wagon so that the small washers, lock washers
and the nut (part K) are secured on the underside of the wagon.
Attach the Turntable (part D) to the Steering Assembly (part J). Attach the
Steering Assembly to the Turntable using the 1-1/8” Bolt with Hole. Slide the
Bolt through the underside of the Steering Assembly (J) and into the Turntable
(part D). Secure it from inside the Turntable with the 7/8” Washer, the Large Lock
Washer and the Hex Nut. Loosely thread the Hex Nut onto the Bolt. Insert the
Cotter Pin through the hole and spread it open.
Step 5)
Step 6)
#32826
Attach both parts (now one assembled unit as shown in Step 4)-the Steering
Assembly (part J) and the Turntable (part D), to the Tray (A). Insert each of the
four (4) 1/2” Bolts from the top of the wagon and tighten it into place from the
bottom of the Tray with four (4) small washers, four (4) small lock washers and four nuts.
Slide each of the four (4) Wheels (part C) onto an axle with the Air Valve facing
out. Slide two (2) 1-1/4” Washers onto each axle, one on each side of the Wheel.
After the Wheel and the Washers are in place attach the Cotter Pin to the outside
of the Wheel.
Page 3
Step 7)
Step 8)
Attach each of the four (4) Axle Caps (from Bag part K) to the Axles.
Insert the lower part of the Handle (part B) into the Steering Assembly (part J).
Slide the 2-5/8” Bolt into the Assembly and through the Handle so that it
exits the other side of the Assembly. Tighten the Bolt into place with a Small
Washer and Nut Cap.
Step 9)
Turn the Wagon upright. Attach one (1) of the Long Side Panels (part E) to the
wagon with the three (3) 1-3/4” Bolts going through both the Tray and each vertical slat.
The top of the Bolts should be on the inside of the Tray. Tighten each into place with a
washer then a Nut Cap.
Note:
The Short Front Panel (part G) is the one with a downward curved front slat.
Step 10)
Attach the Short Rear Panel (part F) to the wagon with two (2) 1-3/4” Bolts going
through the Tray (A) and each vertical slat. Tighten into place by sliding on the
washer followed by the Nut Cap.
Step 11)
Attach the second Long Side Panel (part E) as in step 9. Attach the Short Front
Panel (part G) with two (2) 1-3/4” Bolts. Tighten into place with the Washer and
Nut Cap as previously described.
Operation
Your Wagon has a long handle mounted at the front. Use the handle to pull the wagon to your destination, as
well as transporting loads to and from your destination.
Turning the Handle (part B) will cause the front wheels on the wagon to turn. Turn the Handle in the direction
that you wish the wagon to go. The Handle can be raised for steering from inside the wagon, or lowered so
that the wagon can be pulled from in front.
if t h e r e is a n y q u e s t io n a b o u t a c o n d it io n b e in g s a f e o r u n s a f e , d o n o t o p e r a t e t h e Wa g o n .
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE
IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OFTHE PRODUCT. IN FACT,THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER.THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT
OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF
REPLACEMENT PARTS THERETO.
#32826
Page 4
REV 02g
Unpacking
When unpacking your Big Foot Panel Wagon, check to make sure the following parts are included. If any
parts
are missing or broken, please call Harbor Freight Tools at 1-800-444-3353.
Parts List-#32826
Part #
Description
Tray
Handle
Wheels
Turntable
Long Side Panel
Short Rear Panel
Short Front Panel
Rear Axle Assembly
Rear Axle Braces
Steering Assembly
Qty
1
1
4
1
2
1
1
1
A
B
C
D
E
F
G
H
I
K
Assembly Hardware Bag Contains:
All bolts are 6mm thread, and include a flat
washer and nut to match.
Qty
1-3/4” round head bolts w/nuts & washers
2-5/8” round head bolt (handle)w/nut & washer
1/2” flat head bolts (axle & steering yoke fasteners)
w/nuts & washers
8
1
16
cotter pins (wheels)
large flat washers (wheels)
Axle caps
4
4
4
1
1
2
1
J
1-1/8” Bolt with hole
7/8” Washer, large lock washer
and Hex Nut (attaching Turntable to Steering
Assembly)
Assembly Diagram-32826
#32826
Page 5
REV 02g
|