NPB-MDM Modem Card
INSTALLATION INSTRUCTIONS
SAFETY INSTRUCTIONS
GENERAL
•
Keep these Installation Instructions for industrial safety
and the prevention of accidents.
•
Only qualified personnel shall do mounting and
installation work with these devices, see section titled
“Qualified Personnel”.
CAUTION
This modem may require testing and
certification in some European and Asian
countries prior to connecting to the Public
Switched Telephone Network. Refer to the
particular country’s telephone authorities for
further information.
•
The information in these instructions must be read and
understood by every person using this device.
QUALIFIED PERSONNEL
Qualified personnel in the sense of these instructions are
persons who are well versed in the use and installation of
such devices and whose professional qualifications meet
the requirements of their work.
This document covers the mounting and wiring of the
NPB-MDM Modem Card in a Honeywell WEB-201
Controller. For related WEB-IO mounting and wiring
details, refer to the WEB-201 Controller Installation
Instructions, form no. 95-7722.
This includes, for example:
•
Qualifications to connect the device according to
applicable specifications and regulations, and
qualifications to put this device into operation, to power
it down, or to activate it by respecting the internal
directions.
Knowledge of safety rules.
Knowledge about application and use of the device
within the equipment system.
The Honeywell NPB-MDM Modem Card uses a 56kbps
auto-dial, auto-answer modem with one RJ-11 connector
for the phone line. The NPB-MDM Modem Card must be
installed in Option Slot 1 only, where it operates as
COM1. This disables the RS-232 base serial port (DB-9
connector) on the WEB-201 Controller. Only one
•
•
NPB-MDM Modem Card is supported in a WEB-201
Controller. Refer to Fig. 2 for location of option slots.
BEFORE INSTALLATION
SAFETY INSTRUCTIONS
1. Unpack the NPB-MDM Modem Card.
2. Check the equipment and report any damage to a
Honeywell representative.
3. Read all of these instructions and ensure they are
understood.
NOTES REGARDING DEVICE DESCRIPTION
These instructions include indications for use and
mounting of the device. In case of questions that cannot
be answered with these instructions, please consult the
product supplier or manufacturer. It is the responsibility of
the equipment installer to ensure that all federal, state and
local codes are followed.
Included in this Package
Included in this package are the following items:
•
One NPB-MDM Modem Card, along with connector
and end plate.
•
INSTALLATION INSTRUCTIONS form no. 95-7730.
Materials and Tools Required
The following tools and supplies may be required for
installation:
—
#2 Phillips screwdriver: used to install the NPB-
MDM Modem Card.
95-7730
NPB-MDM MODEM CARD
WIRING
SERIAL SHELL NOTES
Connect a standard RJ-11 telephone cable to the
connector on the NPB-MDM Modem Card and the other
end to the working PSTN (dialup) telephone receptacle.
If an NPB-MDM Modem Card is installed and the WEB-
201 Controller’s “Mode Jumper” (Refer to Fig. 4) is put in
“Serial Shell” position, the WEB-201 base RS-232 port
becomes active immediately following a reboot. This
allows an RS-232 connection to the “Serial Shell” for
debugging purposes. The NPB-MDM Modem Card is
inoperative during this period.
LEDS
A single LED is visible on the top of the NPB-MDM
Modem Card (cover must be removed from the WEB-201
Controller). This LED is shown on the top label of the
NPB-MDM (refer to Fig. 1) and operates as follows:
To re-enable the modem, the Mode Jumper must be put
back in the NORMAL position, and then reboot the
WEB-201 Controller.
•
ACTIVE (green) — When lit, it indicates that the
modem is connected to another modem (a carrier is
detected). In this case, the WEB-201 serial port LEDs
(on its lower base board) should indicate transmit and
receive activity.
3
95-7730
NPB-MDM MODEM CARD
Automation and Control Solutions
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
customer.honeywell.com
Honeywell Limited-Honeywell Limitée
35 Dynamic Drive
Scarborough, Ontario M1V 4Z9
® U.S. Registered Trademark
© 2006 Honeywell International Inc.
95-7730
J.I.
04-06
|